Sundance Spas New Version Pump 115 Volts, 1.5 HP, 2 Speed 3" Plumbing Replaced Emerson T55CXBLJ-962

Spa Pump for Sundance Spas

6500-135, 6500-258, 6500-758, 6500-345

Specifications:

• 13.8/3.8 Amp

• 2 Speed

• 1.5 HP

• 110-120 Volt

• 48 Frame

The Pump is complete with a Motor and wet end.The difference between the Factory Pump and ours is that ours comes with the original welded bracket on the motor instead of the bracket mount currently used by Sundance. Our pump replaces the original found in your spa that had the mounting bracket welded to it.

This can be used for other spas by simply adjusting the position of the wet end by loosening the 4 bolts (this is a thru bolt motor) and turning the wet end to the position of the original pump and then retightening the 4 bolts. We send the pump in the 6500-258 position which is in the 3:00 position.

Notes:

• We use only a Viton Seal on our Wet ends for long life. The viton seal is designed for harsh chemical environments such as salt, ozone and chemically treated water.These seals are more costly than a standard seal used by most of our competitors.

• Do not install any 1.5 Hp Pump that has a higher Amp Draw (such as the Waterway 3420610-10). This could damage the Circuit Board and trip the GFI from too high of current load.

• This 120 Volt Pump is the Current Replacement for these old part numbers: 6500-135, 6500-258, 6500-758, 6500-345

Used on the Following Sundance Spa Models:

• Aspen - 1998-1999

• Bali - 2000-2003

• Cheyenne - 1998

• Denali - 2006+

• Hermosa - 2003-2004

• Lagunas - 2003-2005

• Metro - 2004-2005

• Redondo - 2003-2004

• Tacoma - 2006+

• Vail - 1998-1999
• 2005-2009 (end date changes with different models): Sundance Spas went to the 6500-345 on most models listed. The difference is that the pump and motor did not have a welded foot bracket so that the pump would fit any configuration. Pump housings are universal and can be rotated to any configuration. This can be used for other Sundance pumps by adjusting the position of the wet end. Simply loose the rear 4 bolts (this is a thru bolt motor) and turn the wet end to the position of the original pump then retightening the 4 bolts.

Used on the Following Jacuzzi Spa Models:

• J-310 - 2002-2003 (#1 Pump)

• Hermosa, Redondo 2002-2004 (#1 Pump)

• J-315 - 2004-2007+ (#1 Pump)

• J-220, J-210 - 2005-2007+ (#1 Pump)
• J-325 - 2008+ (#1Pump)
• 2005-2009 (end date changes with different models): Jacuzzi Spas went to the 6500-345 on most models listed. The difference is that the pump and motor did not have a welded foot bracket so that the pump would fit any configuration. Pump housings are universal and can be rotated to any configuration. This can be used for other Sundance pumps by adjusting the position of the wet end. Simply loose the rear 4 bolts (this is a thru bolt motor) and turn the wet end to the position of the original pump then retightening the 4 bolts.

This pump can be used for the following pump numbers by rotating the wet end to match the position of the original pump.

• 6500-259

• 6500-258

• 6500-293

• 6500-345

• 6500-759

• 6500-758

• 6500-793

Additional Information:

For parts for this pump, click here.